Signal

Tags

Ziegler V604-II programmable Transmitter

Programable universal transmitter , V604-II converts the variable - a DC current or voltage or a signal from a thermocouple , resistance thermometer , remote sensor or potentiometer to proportionate analogue output signal .

View Details

Isolator

Isolating amplifier Ziegler TV808 , finds its applications for isolation, amplification and conversion of DC signals .The DC signal isolator serves to electrically isolate the analog DC signal in the range from 0(4)-20mA which , depending on version, is then converted to a current signal 0(4)-20mA or voltage signal 0(2)-10V.

View Details

Signal Isolator

Isolating amplifier Ziegler TI816 , finds its applications for isolation, amplification and conversion of DC signals .The DC signal isolator serves to electrically isolate the analog DC signal in the range from 0(4)-20mA which , depending on version, is then converted to a current signal 0(4)-20mA or voltage signal 0(2)-10V. It does not require a separate power supply .

View Details

Ziegler TI807 DC Signal Isolator

Isolating amplifier Ziegler TI807 , finds its applications for isolation, amplification and conversion of DC signals .The DC signal isolator serves to electrically isolate the analog DC signal in the range from 0(4)-20mA which , depending on version, is then converted to a current signal 0(4)-20mA or voltage signal 0(2)-10V. It does not require a separate power supply .

View Details

DC Multifunction meter

Ziegler EM DC series is specially designed to measure, display and communicate DC Voltage, Current, Power and Energy to monitor and control the target system. It can be mentioned as its applications in below : -Solar Photovoltaic Systems -Battery chargers and systems -Wind Power Generation -Electroplating Industries -Power Distribution for Telecommunication -Industrial DC control Systems

View Details

AC current single function transducer

The current transducers type TAC-311DG are transducers for measurement of a sinusoidalAC current converted into a DC current signal proportional to the measured value on a single phase or 3 phase network. PLCs, PCs, microprocessor control, indicators, alarm units etc. can be operated by the output signal.

View Details

AC current single function transducer

The current transducers type TAC-321DG are transducers for measurement of a sinusoidal AC current converted into a DC current signal proportional to the measured value on a single phase or 3 phase network. PLCs, PCs, microprocessor control, indicators, alarm units etc. can be operated by the output signal.

View Details

Multi-transducer

The MTR-3 is intended for measuring and monitoring single-phase or three-phase electrical power network. The MTR-3 measures RMS value by means of fast sampling of voltage and current signals, which makes the instrument suitable for acquisition of transient events. A built-in microcontroller calculates measurements (voltage, current, frequency, energy, power, power factor, THD phase angles, etc.) from the measured signals.

View Details

Frequency relay

The digital, combined under-frequency and over-frequency relay type RMF-112D forms part of a complete DEIF series of relays for protection and control of generators. The relay is type-approved by major classification societies and is applicable to both marine and land-based installations. The RMF-112D is applied for protection against under-frequency and over-frequency by supervising the frequency (of generators) in single phase and 3-phase networks.

View Details

Check Synchronising Relay

The CSQ-3 is a microprocessor-based synchronising unit. It can be used in any kind of installation where manual or semi-automatic synchronising is required. Two versions optimised for land or marine applications exist. The unit measures the busbar (UBUSBAR) and generator (UGEN) voltages and frequencies and compares these, plus compares the phase angle relationship.

View Details

Read Synchroscope

The RSQ-3 is a microprocessor-based synchronising unit, providing visual indication of relevant values for synchronising a generator to a net (busbar). It can be used in any kind of installation where manual synchronising is required. The unit measures the busbar (UBUSBAR) and generator (UGEN) voltages and frequencies and compares these, plus compares the phase angle relationship.

View Details

Electronic potentiometer

The electronic potentiometer type EPN-110DN forms part of a complete DEIF series of relays for protection and control of generators, and is applicable to both marine and land-based installations. The potentiometer converts the relay output of a PI step controller - for example one of the DEIF load sharing units type LSU.. or one of the DEIF synchronisers type FAS.., or any other type of PI step controller provided with relay outputs - to a control voltage for the speed governor/AVR.

View Details